I just wanted to remind everyone that the meeting is tomorrow. I know i almost forgot.
Cock'N'Bull Pub at 6:30pm
:beer:
Cock'N'Bull Pub at 6:30pm
:beer:
|
|
|
OVO Meeting.
- Thread starter chunkytrunks
- Start date
D
Dirk
Guest
I'll be there with DVD's. How large is the file?
its too bad im in toronto. id definatly join ovo and become a member and, and attend the meetings.
oh well ill just have to wait for an ovo chapter in t.o:clue:
oh well ill just have to wait for an ovo chapter in t.o:clue:
I still have some clothing orders to be picked up, I will have that at the meeting with me..
Tim
Tim
Billygoat
Well-known member
Damn. Can't make it again.
Tim, I just may bug you again about dropping into Kanata some day during lunch to pick up my stuff.
Dues are due March 30, correct? I may get that done with EMT now (Email according to another thread is treasurer@ovo.ca).
M
mcgee
Guest
wont make it either to this meeting. engine rebuild at work.
twin cam set up for duel fuel pumps per cylinder.24 in total.
rering 24 pistons and changed one liner then on reassemble i found
a crack on the top crank shaft! aagh not good.
next time
twin cam set up for duel fuel pumps per cylinder.24 in total.
rering 24 pistons and changed one liner then on reassemble i found
a crack on the top crank shaft! aagh not good.
next time
D
Desert Storm
Guest
count on me, i'll be there for sure. bringing an ex-ovo buddy of mine also!!
G
Grumpy
Guest
I am bringing my Titan Air Compressor for Show and Tell
I'll have the Tsunami for our 'Air Off '.......
Loco
I'd wheel it
D
Desert Storm
Guest
well i'll make some! used to have the xj stuff to the top by the gf so there's nothin there
c u there then.
c u there then.
G
Grumpy
Guest
Me? Early?............hahahahahahaha....yeah right, nice thought but no such luck....I'm bringing 2 BFG MT's 31X10.50X15 on zuk rims......I'll have the valve cores out prior to arriving (as to allow both tires to be down to and equal zero pressure), and when we're ready for the test we'll put the cores back in and hook up each pump to each tire and let'em go for a prescribed amount of time, at which point we'll measure how much pressure is in each tire.....At that time we'll also check the heat generated from each unit...(looking for volunteer skin at that point...lol). As far as current draw, we could get one of the techo geeks to weigh in on the situation with some sort of device...ohm meter or whatnot....but I repeat I will not be able to make it there early......it's a given. See ya when I get there....
:rainbow::rainbow::flipoff::flipoff:
Terry will have to bring his Power Tank and own you both
Hahahaha
Sent from my iPhone
Sent from my iPhone
On 26-Feb-09, at 2:35 PM, "aweber" wrote:
Quote:
Originally Posted by Grumpy
Me? Early?............hahahahahahaha....yeah right, nice thought but no such luck....I'm bringing 2 BFG MT's 31X10.50X15 on zuk rims......I'll have the valve cores out prior to arriving (as to allow both tires to be down to and equal zero pressure), and when we're ready for the test we'll put the cores back in and hook up each pump to each tire and let'em go for a prescribed amount of time, at which point we'll measure how much pressure is in each tire.....At that time we'll also check the heat generated from each unit...(looking for volunteer skin at that point...lol). As far as current draw, we could get one of the techo geeks to weigh in on the situation with some sort of device...ohm meter or whatnot....but I repeat I will not be able to make it there early......it's a given. See ya when I get there....
Terry will have to bring his Power Tank and own you both
BillaVista
PrettyBoy
Can I bring my 2500 psi Nitrogen tank?
Or what say we say screw it...ether...match..woof...done!
Or what say we say screw it...ether...match..woof...done!